PAGE 8
RETURN
R
L
SEND
INSTRUMENT
INPUT
FOOTSWITCH
FX
CH
MAIN OUTPUT
OUTPUT
R
L
EFFECTS
LOOP
50%
0%
100%
MIX
LEVEL
AUTO SOLO
SW.
AUTO CLEAN
FOOT
MAIN OUTPUTS:
These Left / Right MAIN OUTPUT Jacks provide two outputs, left and right, for interfacing to power
amplifiers or directly to your effects units. The OUTPUT
Control allows you to vary the amount of signal going out of
theV-TWIN and in to whatever it is connected to.
REAR PANEL:
ON / L IFT
EXTERNAL CHANNEL SELECT
SOLO 1
SOLO 2 SOLO 3
CLEAN 1
CLEAN 2 CLEAN 3
POWER
ON
HEADPHONE
OUT
RECORD OUT
R
L
INSTRUMENT
INPUT
FOOTSWITCH
FX
CH
MAIN OUTPUT
OUTPUT
R
L
LEVEL
RETURN
R
L
SEND
AUTO SOLO
SW.
AUTO CLEAN
FOOT
EFFECTS
LOOP
50%
0%
100%
MIX
INSTRUMENT INPUTS:
The Instrument Jack located on the Rear Panel and to the far right is just one of two Instrument
Jacks that are provided on the V-TWIN. This jack is provided to accommodate those who wish
to use the unit in a rack type set-up, where the input signal is derived from a master rack input routing system or
switcher. The Instrument Jack on the Front Panel and to the left, is the same and in no way sonically different. It
was added to facilitate quick set-ups and on-the-fly type situations.
INSTRUMENT
INPUT
FOOTSWITCH:
These two 1/4 inch phone jacks are provided to accept the Channel Select Footswitch ( that should have
come with your V-TWIN ) and the ( optional ) Effects Loop Footswitch. When either or both of these
footswitches are connected to these jacks, you will be able to select the channel of your choice and / or
the Effects Loops' status remotely.
INSTRUMENT
INPUT
FOOTSWITCH
FX
CH
NOTE REMEMBER...that to switch the CHANNELS with the remote Footswitch, you must have
both of the Front Panel manual footswitch mini toggles set to the FOOTSWITCH position.
EFFECTS LOOP:
The V-TWIN incorporates a Parallel Effects Loop to insure that your Tone stays as pure as possible, free
from degradation caused by processors that might use less than optimum operational amplifiers in their mix and output stages. The
Loop is comprised of a MONO SEND and STEREO RETURNS. It also features a MIX Control for determining the Dry / Wet blend.
Activation of the loop is acheived by selecting one of the three Loop Active positions
on the MANUAL / AUTO mini toggle switch located just below the SEND jack.
To use the Effects Loop for processing the V-TWIN sound; Simply, Connect the
SEND jack of the Effects Loop to your processors INPUT. Connect the two RETURN
jacks (one RETURN if you have an effect with a MONO Output) to the processors Output
jack. Select the Mode of activation you wish to use with the MANUAL / AUTO mini
toggle i.e. (AUTO SOLO or AUTO CLEAN) if you don't need to footswitch the Loop in and out. Set the Dry / Wet mix of your
processor to 100% wet. Dial in the desired amount of effect you wish to hear with the Effects Loop MIX Control. Go Off !
4
1
6
2
5
3
NOTE By following the suggestion of setting your processors Dry / Wet Mix Control to 100%, you will automatically set the V-
TWINS' MIX Control closer to a "0%" blend of the loop and dry signal ratio. This scheme is almost always the best way to insure
that your sound stays bold and expressive because you will be introducing very small amounts of outside and possibly unfriendly
circuitry into the V-TWIN'S signal path.
RETURN
R
L
SEND
AUTO SOLO
SW.
AUTO CLEAN
FOOT
EFFECTS
LOOP
50%
0%
100%
MIX
(13 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals