EXTERNAL CHANNEL SELECT:
TheV-TWIN can be controlled by an external switching source to select between
the different Modes. This can be most any tip to ground type switch
logic. This feature makes possible the inclusion ofV-TWIN into
programmable rigs or multiple pre-amps where the units within are
controlled by a programmable switcher.
ON / L IFT
EXTERNAL CHANNEL SELECT
SOLO 1
SOLO 2 SOLO 3
CLEAN 1
CLEAN 2 CLEAN 3
POWER
ON
NOTE V-TWIN must remain in the power-up switch logic to be controlled via this jack. In other words...every time you get
ready to use the unit in an External Select situation, remove the A.C. adaptor and plug it back in without choosing any
Modes...Leave it alone. This procedure clears the switching logic leaving the circuit in the receive-ready state and awaiting
commands from the external switching device.
HEADPHONE OUT:
When a pair of stereo headphones are connected to this jack, stereo phoning is accessible to you
because while the output level remains constant, the tip is
connected to ring internally on the jack which makes this feature
possible.
Use the MASTER VOLUME Control ( Front Panel ) in either
channel depending on which channel you are using at the time,
to adjust the listening level. Keep in mind that the type and quality of headphones that you are using, greatly affect the
performance of this circuit, with the fully enclosed - studio type producing the best results.
RETURN
R
L
SEND
MAIN OUTPUT
OUTPUT
R
L
EFFECTS
LOOP
50%
0%
100%
MIX
LEVEL
AUTO SOLO
SW.
AUTO CLEAN
FOOT
HEADPHONE
OUT
RECORD OUT
R
L
RECORD OUT:
RETURN
R
L
SEND INSTRUMENT
INPUT
FOOTSWITCH
FX
CH
MAIN OUTPUT
OUTPUT
R
L
EFFECTS
LOOP
50%
0%
100%
MIX
LEVEL
AUTO SOLO
SW.
AUTO CLEAN
FOOT
HEADPHONE
OUT
RECORD OUT
R
L
both SOLO and CLEAN Channel sounds similar to
those you are accustomed to hearing from your
power amp and speakers. The output level is
determined by the Front Panel MASTER Control
setting. At extreme settings it may be possible to
overload the console's input circuit. Medium
MASTER Control settings are probably sufficient for most situations. Check your levels.
These jacks provide direct stereo interfacing to recording or live mixing consoles. They faithfully reproduce both SOLO
The "Euro Style" A.C. cord connector that is supplied with theV-TWIN makes set-ups and tear-
downs after the gig a snap. It also makes de-racking much easier when you wish to remove the unit
from a hard wired rack system where all the A.C. cords have been cut to length. Additional heavy duty cords are
available should you ever need one...simply call us direct and we can ship one directly to you for a nominal
charge, plus shipping costs. Make sure the A.C. Cord is firmly in its socket (receptacle) before powering up the
unit.
A.C. RECEPTACLE:
ON / L IFT
POWER
ON
PAGE 9
POWER ON & ON / LIFT:
This is theV-TWINS' main power ON / OFF Switch. The two way rocker switch also
functions as a ground lift for adverse polarity problems that you could
encounter from time to time. As a reminder, it is always a good idea
to turn the volumes down on your power amp before switching the V-
TWIN on - this will prevent possible damage to your speakers from
any sudden loud pop that could be amplified...not to mention, saving
your ears for more important things, like hearing your music.
ON / L IFT
EXTERNAL CHANNEL SELECT
SOLO 1
SOLO 2 SOLO 3
CLEAN 1
CLEAN 2
POWER
ON
(13 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals